Metal roofing
Architectural shingles
Tile roofing
GAF
Owens Corning
Flat & low-slopeFree roof inspection with deck photos before we talk money - GAF and Owens Corning certified installation
Fast, Reliable Roof Replacement Across Culver City
Roof replacement in Culver City runs $14,500 to $32,000 for a typical single-family home, depending on material and roof complexity. We work across all of Culver City’s ZIP codes, 90230 through 90233, from the Spanish bungalows off Sepulveda to the mid-century ranches near Veterans Park. Our crews know which streets carry the heaviest marine layer and which trees drop the most leaf litter, because our team has torn off and rebuilt roofs on nearly every block type in this city. Call (833) 589-7971 and we’ll give you an honest, line-item estimate, not a sales pitch.
Why Hollywood Roofing Co Is Culver City’s Preferred Roof Replacement Company
Culver City homeowners call us because we show up when we say we will and because we understand what this city’s specific climate does to a roof over 20 years. The marine layer that rolls in off the Ballona Creek corridor doesn’t just make mornings gray. It carries salt-laden moisture that settles onto low-pitch and north-facing roof sections and quietly chews through cheap hardware while the shingles still look fine from the street.
We’ve torn roofs off in Carlson Park, Blair Hills, and the downtown blocks near Culver Boulevard, and we know what’s waiting underneath before we lift the first tile. That’s not something a crew from the Valley or Orange County can say without years of Culver City tear-offs behind them. Roland Vega, our owner, has built the company around that kind of block-by-block familiarity.
Our customers in Culver City consistently tell us the same thing: the estimate was clear, the crew was tidy, and the roof looks even better than they expected. We hold ourselves to a standard that works in a city where neighbors live close enough to notice whether a job site is run cleanly. Call (833) 589-7971 to talk through your roof.
Styles & brands we work with
Reroofing in Culver City
Reroofing in Culver City usually means stripping the existing shingle or tile layer down to the decking, repairing or replacing whatever the marine layer has compromised, and installing a new roofing system in one continuous pass. For a standard composition shingle reroof on a mid-century ranch in the 90230 or 90232 ZIP, expect to pay between $14,500 and $21,000. For a tile-to-tile reroof on a Spanish Colonial in Carlson Park or the older streets near downtown, the range pushes to $22,000 to $32,000 once decking, underlayment, and fastener upgrades are factored in.
Decking and Underlayment Work
What we find under a Culver City roof often matters more than what sits on top of it. North-facing slopes that stay damp for months at a time develop soft decking, and we won’t lay new shingles over compromised plywood or skip sheathing. When decking needs replacing, we quote it as a line item, explain exactly how many sheets are involved, and don’t bury the cost in a vague “materials” bucket.
Clay and Concrete Tile Reset
Many Culver City tile roofs fail from the inside out. The tile itself can last 50 years, but the original galvanized nails holding it down may be rusting to nothing after 25. We reset existing tile where it’s still sound, replacing the underlayment and fasteners beneath it so the roof’s next failure point is the tile itself, not the hardware.
Flat Roof Replacement in Culver City
Flat roof replacement in Culver City is its own discipline, and the city has plenty of it, from 1980s soft-story apartment buildings near the Culver City Arts District to modern low-slope additions on post-war bungalows. Flat and low-slope systems, typically built-up asphalt, modified bitumen, or single-ply membrane, run $14 to $22 per square foot in Culver City when full tear-off and new insulation are included. Smaller residential flat sections, like a garage or a back addition, land closer to $8,000 to $14,000 total.
Low-Slope Drainage Failures
Flat and low-slope roofs in Culver City fail most often at the drains and scuppers, especially where jacaranda and ficus debris washes down from surrounding trees and packs the outlets. We rebuild the drainage path as part of every flat roof replacement, sloping insulation to move water off the surface instead of letting it pool and accelerate membrane wear.
Membrane Selection
The right membrane for a Culver City flat roof depends on sun exposure and whether the roof carries foot traffic. South and west facing flat sections get baked by afternoon sun, so we spec heat-resistant membranes with properly sealed seams. Where tree debris is constant, we recommend a thicker membrane that can take repeated cleaning without tearing.
Trusted Brands We Service in Culver City
We are authorized installers for seven major roofing brands, so when a Culver City homeowner chooses CertainTeed, Owens Corning, IKO, or Atlas, we install that system exactly to the manufacturer’s spec, not a “close enough” version of it. That matters because a correctly installed architectural shingle roof carries a real manufacturer warranty, and a sloppy install voids it before the first rain. We stock fast-moving shingle colors and standard flashing profiles locally, which keeps turnaround on Culver City jobs shorter than it would be if everything had to come from an out-of-state warehouse. Seven leading brands. One honest recommendation.
See the difference
Before
After
Before
After
Before
AfterCommon Roof Replacement Problems We See in Culver City Homes
- Rusted fasteners on north and low-slope sections. The marine layer in Culver City holds salt-laden damp against these surfaces for months, turning standard galvanized nails into brittle pins while the shingle or tile above still looks passable. We open these sections during every replacement and upgrade to stainless or hot-dip galvanized hardware.
- Leaf litter packed into valleys and gutters. Mature ficus, eucalyptus, and jacaranda overhang hundreds of Culver City roofs. The shaded north slopes catch the worst of the debris, which traps moisture against the underlayment and feeds moss. A replacement roof should account for this with wider flashing at the valleys and, where feasible, advice on canopy management.
- Sun-baked sealant and flashing on south and west exposures. Afternoon sun in Culver City degrades pipe boot seals, counterflashing sealant, and vent collars years before the shingle field wears out. We treat every penetration as a known failure point and rebuild it with materials intended for UV-heavy, salt-air conditions.
- Santa Ana wind uplift on older starter strips. Dry-season Santa Ana events find any missed nailing pattern or rotted starter strip. On tear-off we often discover shingles that were face-nailed incorrectly 20 years ago and held on only by luck. Our replacements follow current nailing patterns for wind uplift resistance, verified on every course.
Pricing for Roof Replacement in Culver City, CA
A full Roof Replacement on a single-family home in Culver City runs $14,500 to $32,000. Composition shingle on a simple ranch roof lands at the low end. Tile reset with new underlayment, upgraded fasteners, and decking repairs lands at the high end. Flat and low-slope sections add $14 to $22 per square foot. Three things move the number: roof complexity, decking condition discovered during tear-off, and whether we’re installing coastal-spec hardware. Coastal-spec costs more up front, usually 8 to 15 percent, and we’ll explain exactly why in the next section. We provide free, line-item, written estimates for every Culver City project, and the number we quote is the number we stand behind unless the tear-off reveals damage no one could have seen from above. Call (833) 589-7971 to schedule yours.
We Also Serve Cities Near Culver City
Our crews work across the Westside and into the adjacent neighborhoods, from Ladera Heights and Century City to Venice and Beverly Hills. If you’re in Culver City proper or just outside the city line, we likely have a crew that knows your block. Call and ask.
Serving Culver City, CA — Our Local Coverage Area
We’re based in the Culver City area and know this community well. Use the map below to see our service coverage — if you’re nearby, we can almost certainly help.
FAQs About Roof Replacement in Culver City
It costs more because we specify stainless or hot-dip galvanized fasteners, marine-grade flashing, and in some cases a heavier underlayment that can tolerate months of salt-laden damp without degrading. Inland roofs can use standard galvanized hardware and electro-plated flashing without early failure. In Culver City, that cheaper spec starts rusting within 8 to 12 years on north and low-slope surfaces, and fixing it later means tearing off a roof that still looks fine. The 8 to 15 percent premium is the difference between a roof that fails at the shingle and one that fails underneath it. Call (833) 589-7971 and we’ll show you both specs side by side.
Hot-dip galvanized is sufficient for most Culver City roof replacements, provided the coating weight is adequate for continuous marine exposure. Stainless is the better choice where the roof is within a few blocks of the Ballona Creek corridor or faces north with heavy tree canopy that keeps the surface damp for weeks. Stainless costs roughly 3 to 5 percent more than hot-dip on a full replacement. We’ll make a specific recommendation for your block, not a blanket upcharge. Call (833) 589-7971 for an honest assessment.
Yes, and it’s one of the more common jobs we do in Culver City’s historic districts. We remove the tile, inspect each piece, and reset the ones that are still sound on new underlayment, new decking where needed, and upgraded fasteners. The tile usually has decades of life left. What fails on these bungalows is what’s underneath: the original galvanized nails, the felt underlayment, and sometimes the decking at the eaves and valleys. Resetting existing tile costs less than a full tile replacement and preserves the original streetscape character. Call (833) 589-7971 and we’ll tell you whether your tile is a candidate for reset.
It affects it in three ways. First, leaf litter packs into valleys and against north slopes, holding moisture against the underlayment and feeding moss. Second, shaded roofs dry more slowly after every marine layer event, which extends the window where hardware is sitting in damp conditions. Third, overhanging branches scrape shingle surfaces and drop debris that clogs drains on flat sections. A proper replacement in a heavy canopy area includes widened valley metal, careful flashing at any tree-adjacent penetration, and often a conversation about whether selective pruning before the job will extend the roof’s service life. Call (833) 589-7971 for specifics on your street.
Put the two bids side by side and check five line items first: decking replacement assumptions, underlayment type and thickness, fastener specification, flashing material, and the shingle or tile product’s exact model number. A cheaper bid usually cuts in one of those places, and in Culver City the cut that matters most is the fastener spec. If one bid lists standard electro-galvanized nails and the other lists hot-dip or stainless, the cheaper bid will cost more within a decade. Ask each contractor to state these five items in writing. We do this automatically. Call (833) 589-7971 and we’ll walk through your current bids with you, no charge, no expectation.
We have one honest recommendation for your Culver City roof: the one matched to your home’s architecture, exposure, and budget, installed with the right hardware for this city’s marine layer. We are a full-lifecycle roofing company. Inspect, repair, or replace, from the first inspection to the final nail. Call (833) 589-7971 to schedule your free estimate, or stop us next time you see our trucks on a Culver City street.
Written by Roland Vega, Owner at Hollywood Roofing Co, serving Culver City and the Westside since day one.